Tools You Need to Set Up a New Tub
Tools You Need to Set Up a New Tub
Blog Article
Everyone has got their personal piece of advice on the subject of How to Install a Bathtub Yourself.
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably challenging project. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and place the new tub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This short article will certainly aid you install a brand-new bath tub in your restroom if you have actually currently bought a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your devices and material list need to comprise the following:
Getting ready for the Setup
To start with, the supporting frame supplied with the bathroom must be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Using both wooden boards under its feet, position the bathtub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bathtub till the spirit level reviews level.
To set up taps, fit all-time low of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water supply as well as check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type ought to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on our other website. Do you know somebody who is serious about the subject? Do not hesitate to share it. Thanks for your time. Kindly stop by our blog back soon.
View Website
Report this page